668C integrated lathe

Комбинированный станок 668С для обработки тонкомера

668C integrated lathe is designed for processing of round undersized trees into rounded logs with a long groove for blockhousing, matched three-edged round cants, beams, floorboard and clapboard blanks, edge board of various sections.

Dimensions of a finished product with allowance for further processing (shrinkage) and tolerances are determined by the customer when ordering.
The price of 668C lathe includes one outfit for one type of lumber. Outfits for other above-listed lumber types are to be ordered additionally.

For further information on 668C lathe refer to the Equipment Certificate.


A log can be cut into precise dimensional lumber of a good surface quality just in a single run. The log undergoes three processing operations: rounding, smoothing and cutting. Lathe 668C calculated outfit.

668C lathe Specification

Input log dimensions, mm
     Maximum butt end diameter
     Minimum length


Feed rate, m/min

0 - 8

Element diameter after rounding, mm


Maximum cutting depth, mm


Dimensions of saws installed, mm
     Register diameter
     Outer diameter

450 (500)

Rotation frequency, rpm
     Rounding head


Drive power, kW
     Rounding spindle


Dimensions, mm


Weight, kg


Distinctive aspects of machine design and furnishing

- Frequency converter for smooth feed rate adjustment.

- High quality bearings of the rounding unit.

- Three sets of cutting tools for the rounding unit.

- One set of outfit.


668C lathe main units

Оцилиндровочный узел

Rounding unit

Rounds a rough log, i.e. after the log passes this unit, it is rounded to various diameters (from 100 to 200 mm) calibrated along its length.

Оцилиндровочный и фрезерный узлы


Rounding and cutting units

After the rounding the element obtains a center line that remains unchanged throughout the procedure. Thus the upper and lower cutter will be symmetric about the center line.

Фрезерный узел

Cutting unit

This unit processes the element from up and down to obtain a desired shape in accordance with the cutting chart.

Пильный узел


Sawing unit

This unit cuts the element into finished dimensional lumber depending on the cutting chart. When log structures are produced, this unit is disabled.

Assembly and installation

The installed lathe should be easily accessible and well-lighted. The lathe is installed on a foundation with the depth depending on the ground type but no less than 600 mm and attached to the foundation by six 16 mm anchor bolts. After the installation onto the foundation the lathe is leveled. The level is mounted onto the foundation. Maximum allowable horizontal deviation is 0,2 mm along 1000 mm. The foundation is then cemented and consolidated; then the anchor bolts are tightened.

Additional information on 668C lathe

1. Warranty
The manufacturer provides a 1 year warranty for all equipment

2. Assembly and maintenance
All machines are equipped with cutting tools (excluding saws, as 668C can use saws of various manufacturers at the user's discretion. Saw specifications are listed in the Equipment Certificate). An additional agreement for commissioning and start-up may be concluded.

3. Moisture of raw materials
This machine is designed for processing of round softwood and hardwood trunks of 3rd grade and above as per GOST 9463-72; GOST 9462-71.

4. Spare parts
The Customer forwards an order for additional equipment or spare parts required, upon its receipt the Seller determines manufacture and delivery time.

5. Machine manufacture time
Machine manufacture time is within 1-1,5 months.

6. Payment terms
50% advance payment and 50% when the equipment is ready for shipment. 3% discount may be granted for 100% advance payment.

7. 668C approximate capacity
Using 0,72 utilization rate for calculation:
- Minimum: 830 running meters per shift;
- Average: 1 900 running meters per shift;
- Maximum: 2 765 running meters per shift.

8. Waste
Chips (after rounding, non-pulp - with bark),
Scrap (after smoothing),
Sawdust (after cutting).

9. Sawdust disposal
Two types of sawdust disposal depending on production facilities are considered (not included into machine price):
- scraping conveyor (preferable);
- pneumatic conveying.

10. Dimensions of materials processed
668C lathe is a feedthrough machine, so the maximum length of a log is of no importance, the only limitation is butt end diameter which should not be over 260 mm. Minimum log length is 1800 mm.

The lathe is equipped with the following tools:

Lathe make Number of knives in a set
Rough knife Finishing knife
668C (rounding) 2 2
668C (smoothing) 4 4

Output variants for 668 integrated lathe for undersized trees processing:

Output sets include:

- 2 cutter housing assemblies;
- knife sets;
- a set of saw blades with flanges;
- rollers for individual cutter layouts (half-blockhouses, floorboards);
- laminated cloth supports (where provided);
- multipurpose roller bushings.

The company develops custom outputs.



Обрезная доска





Половая доска-2


Оснастка №031К Половая доска-3


Оснастка №027К "Имитация под сруб"

Blockhouse imitation

Оснастка №037К "Полусруб"


Обшивочная доска



Оснастка №019К "Шпунтованый брус"

Matched beam